gal kas zinot

sydnex · Post by **sydnex** » 2009-01-31 22:28

sveiki, gal kas galit padeti, pas mane pentium e8400, truputi paturbintas nuo 3.0 iki 3.3 mhz, per sisoftware sandra programa ziurint i procesor raso situos warningus, ka jie reiskia ir ar tai ka nors keicia? ar reikia btvarkyti ka nors?
Warning W227 - CPU FSB higher than rated FSB of the CPU. Even if you’re below the CPU rated speed, by over clocking the FSB you are running the CPU I/O buffers above spec – just be aware of this.

Fix: Reduce the FSB to rated FSB. You can increase the multiplier if the resulting speed is less than CPU rated speed.

Warning W222 - The processor is operating above its frequency specification (rated speed), a condition commonly known as overcloking. The CPU may be unstable or produce erroneous results, some of which may not be readily apparent. The life expectancy will be reduced.

Fix: If you haven’t overclocked it yourself then you should contact the place-of-purchase for an explanation. You may have a remarked processor. To confirm, download the manufacturer’s own utility:

Warning W236 - Processor core voltage (Vcore) is higher than rated maximum. Unless the reported value is incorrect or the processor is a different type that is not correctly detected, the voltage is higher than it should be. If you’re over-clocking the processor you may have pushed too far.

Over-clocking is a condition where the processor is operating above its frequency specification (rated speed). Sometimes the core voltage is increased to improve stability.

Fix: If the BIOS supports processor Vcore setting, check that the voltage programmed is correct for the processor installed. If not, check whether the mainboard supports the installed processor.

arturas173 · Post by **arturas173** » 2009-01-31 22:43

Ne, nekreipk demesio.Cia tesiog perspejama, kad overcklokinimas gali pazeisti procesoriu ir pan.

jtd · Post by **jtd** » 2009-01-31 22:55

jo, bet dar raso kad voltage jau uzkelta auksciau kritines ribos

sydnex · Post by **sydnex** » 2009-02-01 11:40

bet kaip gali buti uzkelta auksciau kritines, gi procas tik 0.3 mhz paturbintas, kiti pasiturbina nuo 3.0 net virs 4.0 mhz, tai kaip jiems nebuna voltage virs?

SoTOP · Post by **SoTOP** » 2009-02-01 11:50

Tai nueik i BIOS ir nusistatyk ta voltage mazdaug 1.2v ir bus ok.

sydnex · Post by **sydnex** » 2009-02-01 22:20

Voltage : 1.251 V
MaxVID : 1.251 V
MinVID : 1.101 V

General information CPU
dabar yra tokie uzkelti, cia jau blogai?

arturas173 · Post by **arturas173** » 2009-02-01 22:57

Normaliai siaip, tau tereikia stebeti temp kad nekaistu pastoviai.O jai uzkelsi temp per aukstai tai pc neisijungs is pirmo karto, o kai bandysi ijungti vel tai isijunks su default bios nustatymais.Dazniausiai reikia tesiog COMOS nuresetint ir viskas. Vienu zodziu nebijok, siais laikas sudeginti ka nors turbinant dauk sunkiau nei anksciau, dbr visokiu apsaugu buna prikista, davikliu ir pan.

sydnex · Post by **sydnex** » 2009-02-02 07:38

del temp, tai visa laika pastovi buna apie 22.5, viena karta tik buvo iki 26 uzkilusi, tai manau nera tiek daug?

Crembo · Post by **Crembo** » 2009-02-02 17:03

Su kokia programa tu tikrini? Nes Wolfdale\'us reikia tikrinti su RealTemp programa.

sydnex · Post by **sydnex** » 2009-02-02 20:56

su pc wizard 2008 programa

sydnex · Post by **sydnex** » 2009-02-02 21:00

su real temp rodo pirma skaiciuka 38 antra 29, tai kiek suprantu temp yra 29

sydnex · Post by **sydnex** » 2009-02-02 21:01

ka tas XS bench parodo?

complexxL9 · Post by **complexxL9** » 2009-02-03 13:41

kame cia logika? uzsiturbini CPU, tada pergyveni, kad tavo CPU uzturbintas.. jei sugebi uzsiturbinti tai gal elementarius angliskus sakinius irgi gali suprasti

sydnex · Post by **sydnex** » 2009-02-03 14:19

Jei buciau pats turbines nieko ir neklausciau nnes viska pats zinociau, apie turbinima isvis nieko nekertu....

complexxL9 · Post by **complexxL9** » 2009-02-03 15:25

na nzn as tai pries turbinima ir uz stabiluma. jei nori uzturbinto cpu ignoruok tuos pranesimus, o jei pranesimai miegot neduoda tai prasyk, kad turbintojas i defaulta viska detu.

sydnex · Post by **sydnex** » 2009-02-03 21:29

ne pats turbinau, jei buciau pats turbines, nieko neklausiau, nes pats zinociau....