Bios pypsejimo problema
-
- Posts: 5
- Joined: 2009-11-27
-
- Posts: 5
- Joined: 2009-11-27
Turbut radau atsakyma kaip sutvarkyt bet angliskai gal paaiskintumet kaip cia viska reik daryt.:
Pros: I made a mistake about how to properly resolve the problem causing the case to beep. The LCD panel on the front of the case can be used to adjust the fan speed of a chasis fan you have installed however to do this the fan must be plugged into the fan power connector that goes to the lcd panel. Otherwise the lcd panel will not be connected to a fan causing it to give a annoying beep error at start up. Just be sure to buy an extra 80mm fan, and be sure to connect it to the power connector that goes to the lcd panel, not to your motherboard otherwise it will continue to beep at start up. The neat thing about the lcd is it will allow you to adjust the fan speed of the fan you connected to the power connector attached to the lcd. This is still a great case and I strongly recommend it.
Cons: annoying beep error at start up if no fan is connected to the power connector attached to the front lcd screen.
Pros: I made a mistake about how to properly resolve the problem causing the case to beep. The LCD panel on the front of the case can be used to adjust the fan speed of a chasis fan you have installed however to do this the fan must be plugged into the fan power connector that goes to the lcd panel. Otherwise the lcd panel will not be connected to a fan causing it to give a annoying beep error at start up. Just be sure to buy an extra 80mm fan, and be sure to connect it to the power connector that goes to the lcd panel, not to your motherboard otherwise it will continue to beep at start up. The neat thing about the lcd is it will allow you to adjust the fan speed of the fan you connected to the power connector attached to the lcd. This is still a great case and I strongly recommend it.
Cons: annoying beep error at start up if no fan is connected to the power connector attached to the front lcd screen.
Ramiai! Nieko draskyt nereikia! Visu pirma chia pypsi pats ekranelis, o ne motinine! Pas mane toks pat korpusas ir pypteli tik pora kartu kaip ir shitam video pora kartu pypteli, poto mazhas tarpelis ir tada ilgai pypsi tai teturi but tie du kartai pypt pypt ir eina. Prie shitos priekines LCD paneles yra tas shilumos jutiklis, maitinimas i ji pasijungia IR YRA ISHEJIMAS AUSHINTUVUI. Pas mane irgi pypsejo nuo pirkimo kol neatlaike nervai ir ishknisau laidu kruva i kuria viskas susukta buvo. Taigi sprendimai:
1. Arba atjungi to LCD maitinimo laido ir jis neshvieschia, nerodo temperaturos ir NEPYPSI.
2. Nusiperki aushintuva korpusui su tryju pin jungtim ir pajungi i ta panele(arba tiesiog atjungi korpuse toki jei jau turi nuo motinines ir pajungi ten, bet butinai tryju pin jisturi but, kitaip nepajungsi). Tada turi geresni aushinima korpuse, matai kad ekranelyje ventiliatoriukas nebemirksi o sukasi, gali su LCD reguliuot apsukas, temepratura korpuse, ir taip pat NEBEPYPSI! Tiesa shitas budas kiek brangesnis(man 12cm fan\'as koki ir rekomenduoju kainavo apie 15lt ).
p.s. Tikiuos spejau priesh ishdraskyma parashyt.
1. Arba atjungi to LCD maitinimo laido ir jis neshvieschia, nerodo temperaturos ir NEPYPSI.
2. Nusiperki aushintuva korpusui su tryju pin jungtim ir pajungi i ta panele(arba tiesiog atjungi korpuse toki jei jau turi nuo motinines ir pajungi ten, bet butinai tryju pin jisturi but, kitaip nepajungsi). Tada turi geresni aushinima korpuse, matai kad ekranelyje ventiliatoriukas nebemirksi o sukasi, gali su LCD reguliuot apsukas, temepratura korpuse, ir taip pat NEBEPYPSI! Tiesa shitas budas kiek brangesnis(man 12cm fan\'as koki ir rekomenduoju kainavo apie 15lt ).
p.s. Tikiuos spejau priesh ishdraskyma parashyt.
-
- Posts: 5
- Joined: 2009-11-27
as imciau nexus : http://www.ptg.lt/lt/prekes/pc_komponen ... uvai/1282/ dejau pas drauge ant cpu ausintuvo, tai tikrai ziauriai tyliai sukasi
-
- Posts: 5
- Joined: 2009-11-27